{"id":9826,"date":"2016-03-31T16:30:14","date_gmt":"2016-03-31T14:30:14","guid":{"rendered":"https:\/\/www.gok-blog.de\/2016\/03\/31\/how-can-i-release-an-opso-sav\/"},"modified":"2026-07-14T13:10:47","modified_gmt":"2026-07-14T11:10:47","slug":"how-can-i-release-an-opso-sav","status":"publish","type":"post","link":"https:\/\/www.gok-blog.de\/en\/how-can-i-release-an-opso-sav\/","title":{"rendered":"How can I release an OPSO (SAV)?"},"content":{"rendered":"

If the OPSO (SAV) has responded to the pressure regulator in an LPG system, it can be easily released again. It is important to know and eliminate the cause of the response of the safety device\u00a0beforehand.\u00a0<\/p>\n

The OPSO (O<\/strong>ver-P<\/strong>ressure S<\/strong>hut O<\/strong>ff) blocks the gas flow if an inadmissible high pressure<\/strong> is present at the outlet of the pressure regulator and in the downstream pipework. We have already explained how it works<\/a>. With GOK fittings with an outlet pressure of 50 millibar, the response pressure<\/strong> of the safety device is c. 120 millibar. If the OPSO, previous designation: Safety shut-off valve SAV, has stopped the gas flow, you must first determine the cause of the fault.<\/p>\n

\n

You might also be interested in<\/span><\/p>\n

Discover more helpful content on this topic.<\/p>\n

See related posts<\/a><\/p>\n<\/div>\n

Requirement<\/h2>\n

If you can exclude the pressure regulator as a source of error, the OPSO can be permanently released<\/strong>. Requirement for this: You must first correct the cause of the overpressure, for example, clean the blocked ventilation line.<\/p>\n

In the following image gallery, you can see how the safety device can be released again. We distinguish between two versions: We supply pressure regulators with a recent year of manufacture with a black plastic cap, previously the cap was made of brass.<\/p>\n

\"\"<\/a>
Unscrew the plastic cap, rotate it through <\/span>180\u00b0<\/span><\/strong>, engage the slot and pull until the spindle clicks noticeably into place.<\/span><\/figcaption><\/figure>\n
\"\"<\/a>
Unscrew the brass cap, rotate it through <\/span>180\u00b0<\/span><\/strong>, engage the slot and pull until the spindle clicks noticeably into place.<\/span><\/figcaption><\/figure>\n

Before releasing, please always close the gas withdrawal and shut-off valve on the consumer equipment and bleed the pressure regulator or the line.<\/strong> After this step, tighten the connections again. If you have rectified the cause of the response of the OPSO, you will find the red\/green visual indicator<\/strong> on the top of the pressure regulator. Now unscrew the protective cap, turn it 180 degrees and attach the groove to the spindle plate. Please pull until the spindle perceptibly clicks into place.<\/p>\n

You can see whether you have properly released the OPSO when you unscrew the visual indicator again. This must be set to green<\/strong> in order to start up the system. Before you do this, please check the system for leak-tightness.<\/p>\n

Useful information about the OPSO (SAV)
\n<\/strong><\/h2>\n

Both the <\/span>German Institute for Standardisation (DIN)<\/span><\/strong> and the <\/span>Technical Rules for LPG (TRF)<\/span><\/strong> specify the required trip pressures for the OPSO. <\/span>DIN 4811<\/span><\/strong> specifies a nominal trip pressure of <\/span>120 mbar<\/span><\/strong>, while allowing a tolerance range of <\/span>95 to 132 mbar<\/span><\/strong>. For <\/span>50 mbar installations<\/span><\/strong>, the <\/span>TRF<\/span><\/strong> specifies only the nominal trip pressure of <\/span>120 mbar<\/span><\/strong> and refers to <\/span>DIN 4811<\/span><\/strong>.<\/span><\/p>\n

Please observe our note that the work on the system described above may only be carried out by a qualified person<\/strong>.<\/p>\n","protected":false},"excerpt":{"rendered":"

Due to overpressure the OPSO (SAV) causes the LPG system to go into fault mode. GOK shows how to release the safety device again.<\/p>\n","protected":false},"author":8,"featured_media":11270,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"footnotes":""},"categories":[396],"tags":[321,347,287,331,332,327],"ausgabe":[],"class_list":["post-9826","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-home-commercial","tag-opso-en","tag-overpressure","tag-pressure-regulator","tag-pressure-relief-valve","tag-safety-equipment","tag-sav-en"],"acf":[],"_links":{"self":[{"href":"https:\/\/www.gok-blog.de\/en\/wp-json\/wp\/v2\/posts\/9826","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.gok-blog.de\/en\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.gok-blog.de\/en\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.gok-blog.de\/en\/wp-json\/wp\/v2\/users\/8"}],"replies":[{"embeddable":true,"href":"https:\/\/www.gok-blog.de\/en\/wp-json\/wp\/v2\/comments?post=9826"}],"version-history":[{"count":3,"href":"https:\/\/www.gok-blog.de\/en\/wp-json\/wp\/v2\/posts\/9826\/revisions"}],"predecessor-version":[{"id":14740,"href":"https:\/\/www.gok-blog.de\/en\/wp-json\/wp\/v2\/posts\/9826\/revisions\/14740"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.gok-blog.de\/en\/wp-json\/wp\/v2\/media\/11270"}],"wp:attachment":[{"href":"https:\/\/www.gok-blog.de\/en\/wp-json\/wp\/v2\/media?parent=9826"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.gok-blog.de\/en\/wp-json\/wp\/v2\/categories?post=9826"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.gok-blog.de\/en\/wp-json\/wp\/v2\/tags?post=9826"},{"taxonomy":"ausgabe","embeddable":true,"href":"https:\/\/www.gok-blog.de\/en\/wp-json\/wp\/v2\/ausgabe?post=9826"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}